Current News Articles - page 69
Daily updated information and news from the plastics industry.
-
New 3D digital technology center in Mlada Boleslav
- 07.08.2013
- Machinery & Equipment
The premises of this new center is to be held next June demonstrations, in which customers of adjacent regions acquainted with the news and get critical information, such specific technical advice. Of course there are technical support and customer service for all equipment supplied. The service...
-
Development of quantity waste from plastic packing
- 06.08.2013
- Plastics recycling
Ministry of enviroment prepares annually the number of reports on the state of the environments. Report on packaging and packaging waste is usually issued with a year's delay. In april 2013 was released report from year...
-
Nordson EFD opens a new showroom and laboratory in Prague
- 31.07.2013
- Machinery & Equipment
Nordson EFD announce that opened a new showroom and laboratory in Prague. Showroom is located on the outskirts of Prague, close to the highway to Brno. It is one of many initiatives that the company EFD intends to celebrate its 50th...
-
Decline in production vehicles in the Czech Republic in the 2nd quarter decreased
- 30.07.2013
- Plastics and Rubber products
In the Czech Republic in the first half of 2013 were produced a total of 589,076 units of road vehicles, as compared to the same period in 2012 represents a decrease in total production of vehicles of 12.83%. Reduction of production is lower than was reported for the first quarter, when it stood at...
-
Conference Forms 2013
The aim of the conference was to provide technical information so that the technicians opened the way to faster design and manufacture of molds, using advanced technologies that can shorten the time and cost of...
-
Kia Motors Slovakia has had a successful semester
Kia Motors Slovakia achieved in the first half of 2013 year increase of 6 percent when produced 158,900 vehicles. Kia in February this year launched series production of the new three-door Kia pro_cee'd late May and began producing the first high-performance version of the Kia cee'd three-door...
-
Music festival Bazant Pohoda was also about the environment
- 23.07.2013
- Plastics recycling
A weekend full of music, fun, games, meetings and interviews is over and after the extraordinary experience of the busy days of the festival Pohoda we are back in reality. ENVI-PAK contributed to its multicultural focus of environmental education supported by photographic competition. Its main aim...
-
Minimizing the preparation time and increase productivity through the use of HASCO fixture A8001
- 22.07.2013
- Plastics Moulds
- Design of molds
- Standardized parts
HASCO fixture A8001 enables cost-type clamping plates and plates for extractors. Time for clamping significantly reduces productivity and machining centers increases...
-
Sheets for exterior and interior from Titan-Tatraplast Ltd.
- 17.07.2013
- Plastics and Rubber products
Compact HPL board are quality large format plates. They are highly durable and are characterized by high durability with minimal maintenance. Choose from a wide variety of colors and motifs. Titan-Tatraplast Ltd. products are 10 year...
-
Engineering Fair on key industry topics
On 7 to 11 October 2013, the Brno Exhibition Centre will host the 55th International Engineering Fair. Organizers expect 1 500 exhibiting companies from all key industries, from machine tools manufacturing to electronics and automation. Who is still considering participation should not linger long...
-
Implementation of tenders for the purchase of materials and services with TRIFID CONSULT a.s.
- 15.07.2013
- Services
The mission of TRIFID CONSULT is to help their clients in business and save costs in business. Since its inception, more than 250 successful projects focused on reducing costs, optimizing organizational and process structures, performance-oriented incentive systems, unblocking bottlenecks and...
-
The LiCEA project will boost the energy savings of Slovak SMEs
The new LiCEA project will be implemented in Slovakia. It will focus on SMEs in plastic industrial sector. The principle of project lies in determination, implementation and long-term usage of Life Cycle Energy Audit. Relevant SMEs can participate and catch the benefits of energy saving...
-
Polyamide TechnylStar ® from RESINEX to increase product quality
- 10.07.2013
- Plastics Processing
- PA Polyamide
RESINEX Czech republic s.r.o. is a polyamide TechnylStar® for excellent surface quality of injection molded parts, exceptional fluidity and possibility of high performance glass...
-
Fasteners Poppit ® for even faster processing
- 08.07.2013
- Plastics and Rubber products
Quick and efficient installation and removal of panels as well as wall and ceiling cladding is a big challenge for fastening technology. The Poppit® fastening system is the solution for this. Through concealed fasteners and the perfect “click” technology, covers can be fastened without visible...
-
Successfully achieving recycling of MSW in Slovakia by EEA
- 04.07.2013
- Plastics recycling
The European Environment Agency (EEA) released in February 2013 on municipal waste management in Slovakia, which assesses the current state and direction of waste...
-
Direct injection of long fibers: new opportunities for the production of stronger, lighter plastics
- 02.07.2013
- Plastics Processing
- Injection molding machines
In general, the longer the fibers are injected, the better mechanical properties of the moldings receive. Direct injection of long glass fibers, however, until recently, could not be made due to the limitations of the material preparation and dosing, but also for the nature of the granules. You can...
-
Interflon Czech s.r.o.: Improvement the characteristics of hydraulic fluids with Teflon ®
- 01.07.2013
- Machinery & Equipment
Hydraulic systems have a unique place not only in industry but also the entire scale non-manufacturing activities. According to its specialization hydraulic systems require different types of high quality hydraulic fluids, which must meet a number of important requirements, such as the ability to...
-
STU developing unique technologies for the regeneration of used oils, research is helping to employ people in the company
- 28.06.2013
- Plastics recycling
Scientists Slovak University of Technology have developed a unique technology for the treatment of motor oils. Thanks to technology there is no need to burn oil, it can be regenerated and reused. Technology began using commercial company in eastern Slovakia. The protected utility model are also...
-
Thermal infrared cameras Optris PI from Hotset CR s.r.o.
- 27.06.2013
- Machinery & Equipment
Are you looking for reliable infrared thermal imager? Need a thermal imaging camera with its lens? See offer powerful thermo cameras brands Optris, which brings the company Hotset CR...
-
Project Don´t fall off from waste at Envirofilm 2013
Between 3 to 8 June 2013 was held on 19 international film festival on environment - Envirofilm. NATUR-PACK had presented the festival in Kosice for two days and a unique courseware "don´t fall off from waste". Directly at the festival it was possible for more than a thousand children from second...
-
Introducing Solberg SK International Ltd. - protect your vacuum pump!
- 25.06.2013
- Machinery & Equipment
Solberg SK International Ltd. is a subsidiary of a leading company in the field of filtration, acting on the world market for 44 years. Our company sells to over 65 countries...
-
New quarters for INCOE®
For INCOE® International Europe, of Rödermark, Germany, the cornerstone laying on June 12, 2013, marks the beginning of the Company’s move into facilities of its own. TFor INCOE®, the project is a decisive step toward optimising efficiencies for customers across all its...
-
KUBOUŠEK Ltd. - Equipment Division presents Digmatic micrometer Mitutoyo MDH-25M
- 21.06.2013
- Machinery & Equipment
Devices division is the sole supplier of a complete range of products, the Japanese company Mitutoyo, manufacturer of measuring instruments and machines for measuring geometric parameters and also supplier of products Italian companies Vici & C and Demmel...
-
Wittmann Battenfeld brings a new connection technology - In-Mold Internal Welding
IMIW has made it possible to overmold inserts with gas- and watertight sealing. The connection is made directly between the contact surfaces by joining the two injection-molded plastic halves from inside, using the same plastic material the parts are made of. This technology is particularly...
-
Products for cleaning and lubrication for food industry from Chem Trend
- 19.06.2013
- Services
Experience professional products for the maintenance of machines made by Chem Trend, which are suitable for the plastics industry. A wide range of pruducts helps our customers to produce quality products and provide fast and efficient cleaning machines, molds and...
-
Controlled liquid ion carbonitriding as an alternative to electroplating
- 18.06.2013
- Machinery & Equipment
CLIN group practices are modern and environmentally friendly processes for the oxidation and carbonitriding steel and cast iron. Diffusion of nitrogen and carbon leads to the layer having non-metallic character. Great advantage of this peripheral zone in comparison to other types of surface...
-
What to do with PVC flooring Fatra affected with floods?
- 17.06.2013
- Plastics and Rubber products
Answers to frequently asked questions. What to do with temporarily flooded PVC flooring? What to do in case of prolonged flooding PVC flooring? We live in a flood area, exposed PVC floor are pulled down, the substrate seems to be all right. How do I know where we can stick the new...
-
Kuboušek Ltd. comes to the global market with a new dimension: GX molding machine from KraussMaffei
- 12.06.2013
- Machinery & Equipment
The crowd of more than 400 guests echoed whisper, as the curtain opened and the view of the first machine of new generation: GX - The new dimension in injection molding. Enthusiastic professional audience, however, could see more. A total of six new series of machines with a clamping force of 400...
-
Cleaning equipment for pipes and heat exchangers from BIO-CIRCLE
- 11.06.2013
- Machinery & Equipment
Bio-Circle Surface Technology s.r.o. presents you RWR-cleaning machine for pipes, heat exchangers and condensers. Time-consuming disassembly and re-assembly of pipes will be through this cleaning technology of the past. Remove rust, oil, mineral or calcium deposits in your systems quickly and...
-
Interplastics, Ltd. offers improvements for your products
- 07.06.2013
- Suppliers of raw materials
- Commodity plastics
Produces an inexpensive compound that improves the properties of the final product. Its use is suitable for film lamination, pipes, injection molding, blow molding, and others. Improve the quality of the final product and its technical properties using...
Branch Dictionary
