A new addition to the product line KVT - FASTEKS ® + - Optimum bolted joints for thermoplastics
Screw FASTEKS KST ® + PLUS represents a perfect bolt joint for thermoplastic materials. Ingeniously designed point angle of 30 ° reduced compared with screws angle greater radial extension. The resulting large axial force then provides uniform dissolution printed plastic.
Boční přesah
Vysokého bočního přesahu i při malé šroubovací hloubce se dosahuje optimálním sklonem. Výsledkem je vysoká předpínací síla při nízkém tlaku na povrch.
Měřitelné výhody
Je možné volit podstatně menší šroubovací hloubku a dimenzovat tak šroubované spoje mnohem levněji.
Délky šroubů, krácení délky a/nebo zmenšení průměru
Nižší stoupání závitu u nového šroubu FASTEKS®+ KST-PLUS umožňuje používat menší nebo kratší šrouby při stejném bočním přesahu.
 | |
Vhodné pro opakovanou montáž
Opakovaná montáž samořezných šroubů bývá nutná kvůli servisu nebo opravám. Aby bylo možné šroub opět zašroubovat, musí být otvor důkladně zkontrolován. Šrouby FASTEKS®+ KST-PLUS byly důkladně testovány už během vývoje a obecně splňují požadavky německé normy VDE 0700.
Geometrie šroubů FASTEKS®+ KST-PLUS má několik zásadních výhod
- Výrazně delší životnost šroubovaného spoje při statickém i dynamickém namáhání
- Optimální spojení a samosvornost termoplastu díky vylepšené geometrii závitu
- Vyšší předpětí díky většímu bočnímu přesahu na nosné straně
- Možnost používat kratší šrouby a/nebo otvory s menším průměrem při zachování stejného zatížení spoje Naši zákazníci tak mohou docílit významných úspor.
- Vyšší torzní pevnost a pevnost v tahu
S případnými dalšími dotazy na šroubované spoje v umělých hmotách se obraťte na naše specialisty.
Rádi Vám poskytnou podrobnější informace.
- autor:
- KVT – Fastening GmbH
You might also be interested
-
Innovation in the world of dosing technology: Movacolor brings a new solution for plastics processing
Movacolor, a leading manufacturer of dosing technology, is bringing innovative solutions for plastics processing in 2024. Innovations include the PTC portable touch control panel and the MDS dosing unit, which increases efficiency and stability in production environments. The new offline dosing...
-
Permanent marking of plastic products and packaging with ultraviolet lasers
- 23.10.2024
- Plastics Processing
- Lasers
Manufacturers of electronic components, pharmaceuticals and packaging, as well as consumer goods, have a fundamental requirement to permanently mark their products, e.g. for traceability, anti-counterfeiting, branding or functional purposes such as scale marking. Labels can be damaged or removed,...
-
History of the Czechoslovak plastics industry in interviews of witnesses (VII./VII.)
- 18.10.2024
- Plastics Processing
- Interview
- Injection molding
The main theme of the memorial talks is sharing the informations. Without this sharing, the early days of the plastics industry would have been much more difficult or we would not be where we are now. The final memorist in the series of the plastics history in Czechoslovakia is Lubomír Zeman,...
-
History of the Czechoslovak plastics industry in interviews of witnesses (VI./VII.)
- 11.10.2024
- Plastics Processing
- Interview
- Injection molding
The sixth part of the series of interviews with the monuments of the Czechoslovak plastic industry with Ondřej Kebrle. From the beginning, plastics were only minimally interesting for communist Czechoslovakia. Technical plastics gradually came here from the West and today their use is very wide....
-
History of the Czechoslovak plastics industry in interviews of witnesses (V./VII.)
- 04.10.2024
- Plastics Processing
- Interview
- Injection molding
In the fifth part of the series of interviews with memorials of the Czechoslovak plastics industry, Jiří Gabriel tells us where his first steps towards the plastics industry began and how he got to simulation programs. The long-time expert in the simulation of plastic injection remembered that too....
-
History of the Czechoslovak plastics industry in interviews of witnesses (IV./VII.)
- 27.09.2024
- Plastics Processing
- Interview
- Injection molding
As the previous interviews describe, the Czechoslovak plastics industry was in its early days dependent on information and technology from Western companies. However, they also had to try new ways, discover dead ends, experience successes and failures. One of the many stories of these companies is...
-
History of the Czechoslovak plastics industry in interviews of witnesses (III./VII.)
- 20.09.2024
- Plastics Processing
- Interview
- Injection molding
Zdeněk Řehulka, who has worked with molds all his professional life, also accepted the invitation as part of a series of interviews with monuments of the Czechoslovak plastic industry. He devoted himself to publishing activities and lectures on this topic, collaborated with the Uniplast association...
-
History of the Czechoslovak plastics industry in interviews of witnesses (II./VII.)
- 13.09.2024
- Plastics Processing
- Interview
- Injection molding
The continuation of the series of interviews with memorials who stood at the birth of the Czechoslovak plastics industry. The second part of memories and stories of Jaroslav Novák and Associate Professor Miloslav Maňas. You can look forward to the next five parts full of history, challenges and...
-
Ampacet PFAS-Free Polymer Processing Aid Masterbatches : Answering existing and future restrictions
- 09.09.2024
- Plastics Processing
- Packaging
- Safety
Ampacet offers an extended portfolio of PFAS-Free Polymer Processing Aids (PPA) that allows to substitue conventional Fluorinated-based PPA masterbatches used in various processes (oriented and non-oriented films, pipe extrusion, cable extrusion...) for the manufacture of multiple end-use...
-
History of the Czechoslovak plastics industry in interviews of witnesses (I./VII.)
- 06.09.2024
- Plastics Processing
- Interview
- Injection molding
In cooperation with ARBURG, we have prepared a series of interviews with memorials who were at the birth of the Czechoslovak plastics industry. We will gradually publish the memories and stories of Jaroslav Novák, Associate Professor Miloslav Maňas, Zdeněk Řehulka, Jiří Gabriel, Ondřej Kebrle and...
Branch Dictionary
